BMCJK - LAMINATED PLASTIC
- MSDS: BMCJK
- Manufacturer: NEVAMAR CORP
- Product Name: LAMINATED PLASTIC
- National Stock Number: 9330-00N024078
Product Identification
Product ID:LAMINATED PLASTIC
MSDS Date:01/01/1990
FSC:9330
NIIN:00N024078
MSDS Number: BMCJK
Responsible Party
ODENTON, MD 21113-1322
US
Emergency Phone: 301-569-5000
Info Phone: 301-569-5000
Preparer: PAUL R. GARTELMANN
Cage: 92570
Contractor
Telephone: 301-569-5000
Cage: 92570
Ingredients
NON HAZARDOUS INGREDIENT
Hazards
LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:INHAL: NOTE: LAMINATE DUST IS SIMILAR
TO WOOD DUST WHICH HAS BEEN CLASSIFIED AS A NUISANCE DUST. INGEST:
NOT APPLICABLE. SKIN: NOT APPLICABLE. EYE: IRRITATION MAY ARISE
FROM EXCESSIVE NUISANCE DUST, E TC.
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:NONE SPECIFIED BY MANUFACTURER.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.
First Aid
First Aid:INGEST: CALL MD IMMEDIATELY . INHAL: REMOVE TO FRESH AIR.
SUPPORT BREATHING (GIVE O*2/ARTIFICIAL RESPIRATION) . EYES: IF
EXPOSURE TO NUISANCE DUST OCCURS FLUSH EYES THOROUGHLY FOR AT LEAST
15 MINUTES. CONTACT MD IF IRRITATION PERSISTS. SKIN: FLUSH WITH
COPIOUS AMOUNTS OF WATER. CALL MD .
Fire Fighting
Extinguishing Media:USE DRY CHEMICALS, FOAM, WATER SPRAY, WATER FOG OR
CO*2 TO EXTINGUISH FIRES.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA & FULL
PROTECTIVE EQUIPMENT . USE WATER SPRAY TO COOL EXPOSED SURFACES TO
FIRE AND TO PROTECT PERSONNEL.
Unusual Fire/Explosion Hazard:CHARACTERISTICS ARE SIMILAR TO WOOD AND
PAPER PRODUCTS.
Accidental Release
Spill Release Procedures:NOT APPLICABLE.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
Handling
Handling and Storage Precautions:CHARACTERISTICS ARE SIMILAR TO WOOD
AND PAPER PRODUCTS.
Other Precautions:FOLLOW SAFE WORK PRACTICES.
Exposure Controls
Respiratory Protection:NOT REQUIRED NORMALLY. USE NIOSH/MSHA APPROVED
DUST RESPIRATOR IF DUST IS PROBLEM WHILE SAWING.
Ventilation:GENERAL MECHANICAL: PROVIDE SUFF VENT & DUST COLLECT WHEN
CUTTING MATL. LOCAL EXHAUST: KEEP TDUST BELOW 10 MG/M3 PEL.
Protective Gloves:CLOTH GLOVES RECOMMENDED.
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:FOLLOW SAFE WORKING PRACTICES.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
NONE SPECIFIED BY MANUFACTURER.
Chemical Properties
HCC:N1
Boiling Pt:B.P. Text:>500F,>260C
Spec Gravity:1.2 @ 70F
Solubility in Water:SLIGHT
Appearance and Odor:SOLID SHEETS WITH SLIGHT ODOR.
Stability
Stability Indicator/Materials to Avoid:YES
NONE SPECIFIED BY MANUFACTURER.
Stability Condition to Avoid:NONE
Hazardous Decomposition Products:NONE
Disposal
Waste Disposal Methods:DISPOSE OF ALL DUST AND CHIPS VIA NORMAL
SANITARY LANDFILL. DISPOSAL MUST BE IN ACCORDANCE WITH FEDERAL,
STATE AND LOCAL REGULATIONS .
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.